A Lined Faux Roman Blind Tutorial

It’s been a couple of years since we moved to our house, and bit by bit we are working our way through all the usual home improvements that will finally make it the home we are after. Painting has been our main focus lately, and we have just finished painting the dreaded hall, stairs and landing followed by the kitchen and utility room. Of course when I say ‘we’ I mostly mean my husband! Haha!

Our utility room had a nasty old (dust gathering) venetian blind, and when this was removed during painting, I decided to crack on with replacing it with something much more lovely to look at.

It’s only a small window, and not one which needs a functioning blind – it is at the back of our house and is not overlooked at all. I had my heart set on a false Roman Blind made from a piece of special Orla Kiely upholstery fabric from Dunelm. It’s a little pricey at £18 per metre, but decided that I might be able to get away with just a half metre as the fabric was plenty wide enough to cover the width of the window and as it wasn’t necessary to be a working blind, I could simply fold it where I liked to make the drop work. So a half metre of this fabric cost me just £9, which I didn’t think was too bad.

The most important thing with this project is to be very precise with your measurements. I wanted this blind to sit just above the window recess, with a few cm ‘overhang’ either side. The window recess measurements are 58cm width and 112cm drop.

I decided that I wanted the finished flat blind measurement to be 66cm in width ( that is the 58cm width of the window plus a 4cm ‘overhang’ each side of the recess). The drop length of the blind is 50cm ( i.e the half metre length that I purchased).

To measure how wide to cut the Orla fabric, I knew I needed the width to be 66cm (width of the finished blind), plus a 1cm seam allowance each side = 68cm. I then wanted there to be a narrow vertical ‘border’ of the Orla fabric on each side of the reverse of the blind where it attaches to the lining fabric. This ‘border’ measures 2cm each side, so the total width that I needed to cut of the Orla fabric was 72cm.

The lining fabric then needed to be cut. I just used some cream curtain lining that I had in my stash, but I’m pretty sure this wouldn’t be too expensive if you had to buy a small amount.

The lining needs to be measured to be slightly narrower than the Orla fabric, as this will allow the Orla fabric to create that lovely ‘border’ on the reverse of the blind that I mentioned previously. So, the lining is calculated as the finished width of the blind (66cm) minus the 2 lots of 2cm borders =62cm, plus 2 lots of 1cm seam allowances = 64cm.

So, to clarify, I cut the Orla fabric at 72cm width, and the lining at 64cm width. This way ensures that when they are sewn together that a nice grey border will run down each side of the wrong side of the blind.

With such precise measurements, it is essential to press your fabric before cutting. I trimmed off the smallest amount of fraying fabric at the top and bottom of my blind (where the fabric had been cut), and I also positioned the design so that the centre line of one of the stem rows would be running down the exact centre of the blind.

Now to get sewing! Firstly, with the right sides together, I pinned and sewed both side seams.

When you have sewn down either side of the blind, smooth that ‘lump’ of Orla fabric so that the vertical seams on the back of the blind are evenly 2cm from the edge of the blind. Don’t iron it yet. Before you turn it right side out, pin along the bottom edge and sew this up. Again I used a 1cm seam allowance to preserve what little length I had.

You can then trim this seam allowance, clip the corners and turn the blind right side out again. Use a point turner or something similar to ensure the corners are nice and sharp and give it a good press.

You can see from the image above that I then pinned the open top edge together. I neated these edges together with the overlocker.

Next it’s time to attach the velcro strip to the top of the blind. The velcro strip that I used is 2cm wide, so I turned over the top edge by 3cm, pressed it, and pinned and sewed the fluffy side of the velcro along the middle of this turn-over.

Next, it is time to pleat your blind. This is done purely on your personal preference. I wanted 2 or 3 folds, and I also wanted to pattern match the stem design too. Take into consideration the height that you will attach the wooden batten to the top of the window too.

When you are happy with the finished folded blind, give it a good press. In addition to pinning it in place, it is a good idea to run some temporary lines of tacking along the folds so that it doesn’t droop whilst you are finishing it off. I also permanently hand stitched the folds at each side of the blind, and also at various intervals along the folds at the back of the blind. Remove your tacking stitches.

The wooden batten that we used to attach the blind to the wall was just a leftover that we had in the garage. Again, when I say we, I mean my husband! He cut it to just short of the 66cm blind width – probably approx 64cm – so that it wouldn’t show at all when the blind was in position. He then stapled the prickly part of the velcro to it, and screwed it to the wall a few centimetres above the top of the window recess.

The blind simply sticks to the batten now, with the velcro, and there you have it! Easy!

I do hope that this might help you if a false Roman Blind is something that you are planning.

Take care, and I’ll be back soon,

Kathy x